LUM series ultrafine vertical mill is a new type of ultrafine grinding equipment designed and developed by Liming Heavy Industry based on 30 years of experience in the research and development and manufacturing of four generations of grinding machines, based on the LM vertical mill, and the introduction of modern ultrafine vertical mill grinding roller technology. It can be widely used in calcite, marble, limestone, heavy calcium, talc, barite, dolomite and other non-metallic minerals. Ultra-fine grinding and processing, it is an ideal equipment for large-scale non-metallic ore milling.
How about the LUM series ultra-fine vertical mill?
1. High grinding efficiency and low pollution of finished materials
A. The principle of material layer grinding is adopted, and the residence time of the material in the mill is short, which reduces repeated milling.The finished product contains less iron, and when it is used to grind white or transparent materials, the whiteness and clarity of the product are high.
B. The grinding curve of the roller sleeve and liner specially designed to realize the principle of ultrafine grinding. When used for ultrafine powder grinding, it is easier to form a material layer than ordinary vertical grinding, so that the mill can grind to the required fineness (0.045-0.02mm) at a time.
2. Energy saving in powder selection technology
A. The principle of a multi-wheel powder separator is adopted, and each rotor can be controlled by frequency conversion, and the fineness of the finished product can be achieved within the selected range. There is no need for secondary wind sorting and grading, and there is no inferior material.
B. Due to the principle of ultrafine grinding and multi-round powder selection, when producing products of the same fineness level, it saves energy consumption by 30% to 50% compared with ordinary mills, and has good economic benefits.
C. High reproducibility in multi-variety production.
The reason for the recommendation of this mill: Due to the use of ultra-fine grinding and multi-head powder selection principle, it can save energy consumption by about 30% to 50%.It also adopts PLC/DCS automatic control of the grinding roller pressure control method, the grinding pressure can be accurately controlled, saving labor costs.
3. Intelligent control system
A. The speed of the host adopts frequency conversion and speed regulation, which is suitable for a wide range of materials.
B. It is equipped with a mechanical limiting device and an electronic limiting device to prevent direct contact between the roller sleeve and the grinding disc liner, which avoids destructive shocks and severe vibration.
C. Adopts PLC/DCS automatic control of the grinding roller pressure control method, and the grinding pressure is controlled without manual operation.
D. The lubrication of the grinding roller adopts a single lubrication station, and the single grinding roller circuit adopts a double pump, and the pumping and suction mode works at the same time. Even if the grinding roller bearing is fully lubricated and cooled, it can ensure that the grinding roller bearing room will not leak due to excessive oil storage.
E. Equipped with an automatic control system, remote control can be realized and the operation is easy.
4. Less wear and tear, easy maintenance, green and environmentally friendly
A. Since the grinding roller is not in direct contact with the grinding disc during work, and the grinding roller and the liner are made of good quality materials, it has a long service life and less wear.
B. The grinding roller can be pulled out to the outside of the chassis for maintenance, and the replacement of the roller sleeve and liner is convenient and fast, reducing downtime losses.
C. The vibration is low and the noise is low; and the equipment is sealed as a whole, the system works under negative pressure, there is no dust overflow, the environment is clean, and it meets the national environmental protection requirements.
LUM series ultra-fine vertical mill quotation
This depends on the actual needs of the user manufacturer and the type of equipment purchased.Different users have different requirements for equipment.The different types and capacities of equipment provided by manufacturers will lead to large price differences in the same equipment, which will affect the investment costs of users.Different market supply and demand and industry competition will lead to different stone mill circulation prices, which will also affect investment costs.Therefore, users try their best to check on the websites of big brand manufacturers, or call the company directly to get discounts and new prices.
If you are interested in Liming Heavy Industry Technology LUM series ultrafine vertical Mill, you can click Online customer service for consultation.
LUM series ultrafine vertical mill Headquarters Address: No.169, Science Avenue, High-tech Industrial Development Zone, Zhengzhou, China